AAP Elite S series Spécifications télécharger pdf (Page 19)

Page 19

USER CODE PROGRAMMING

USER CODE PROGRAMMINGUSER CODE PROGRAMMING

USER CODE PROGRAMMING

USER CODES - (P1E to P100E) & INSTALLER CODE - (P410E)

There are 101 codes available in the panel, 100 user codes and 1 installer code. All Users 1-100 can be unique 1-6

digit codes or Users 21-100 can be programmed as Radio Keys. If a radio key has been loaded as a User, that user

slot is not available to be used as a code. If you enter a user address number and you get a single long error beep,

this indicates that the user is programmed as a radio user. The user codes are located at addresses P1E-P100E. By

default, Code 1 is the Master Code because it has full access to enter Client Program mode. Other user codes can

be programmed as master codes if required. The Installer code is stored at address P410E and is used to access

Installer Program mode.

Codes P1E-P100E may be varied in length from 1 to 6 digits. Code P410E (Installer Code) must be 3-6 digits.

To program a User Code you must first be in client or installer program mode, then enter the address from 1-

100. (If there is already a code programmed at this address, it will be displayed to you after you press the ENTER

button. If the slot has a Radio key user loaded you will get a long error beep when you enter the address).

NOTE: Not all User Codes may have the ability to access Client Program Mode. The installer can restrict access to

Users so that they have No access, Limited Access or Full access to Client Mode as defined at addresses P221E-

P240E.

TO ADD A NEW CODE:

For example to program a code of 5,6,7 for User 50 you would enter the following;

P 50 E

(If a code was there it would be displayed, if not, the display will be blank )

Then 567 E

3 beeps

The new code will now be displayed

TO CHANGE A CODE:

For example to change User code 1 from the default setting of 1,2,3 to 9,8,7,6 you would enter the following data at

the keypad.

P 1 E

(Old code is displayed at the keypad, in this case it will be 1,2,3)

Then 9876 E

3 beeps

The new code will now be displayed

To replace a code simply enter the new code in the same address as the old code. This will overwrite the previous

code but maintain the user permissions assigned by the programmed user group number.

TO DELETE A CODE:

To clear or delete a code simply press and hold

the “CONTROL” button followed within 2 seconds by the “0” button at

the address where the old code is stored.

e.g. P 3 E <CONTROL> then <0> E

3 beeps

This will delete the programmed User 3 code

USER CODE GROUP NUMBER P101E—P200E (Value from 0-20)

Each User code can be assigned a User Code Group number from 1-20. The User Code groups assign the Areas

and Arm/Disarm parameters plus many other options to each User. The groups are fully programmable allowing

control of the various activities a User may perform.

Addresses P101E-P200E relate to Users 1-100. A value of 1-20 is assigned at each address associated with a User.

If the User has a group number of 0 they are not allowed to perform any functions. The options associated with a

User Group are programmed at addresses P201E-P340E.

USER

GROUPS 1-20 ARM/DISARM OPTIONS P201E-P220E

The first set of options for the User groups assigns the Areas that each group is allowed to Arm or Disarm as well as

whether it can Arm/Disarm the full alarm, Stay Mode or both. If the User Group is required to allow direct output

control (see P281E-P320E), all of these options must be turned off for the output programming to work.

1 2 ... 14 15 16 17 18 19 20 21 22 23 24 ... 102 103

Commentaires sur ces manuels

Pas de commentaire

AAP Elite S series Spécifications Page 19

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité AAP Elite S series